01473 710946
Your Basket is empty
Coastal DCC Logo
Coastal DCC for Modellers by Modellers
Home » Products » Tam Valley » Hex Frog Juicer Universal
Hex Frog Juicer Universal

HFJ003

Tam Valley -
Hex Frog Juicer Universal

This item is in Stock and available for dispatch
Our Price
£79.00


Which Frog Juicer?
ProductNo of frogsNo of reversing sectionsBooster SizeTrip CurrentElectrofrog/live points?Usage
Hex Frog Juicer61 to 3 selectable1.7-5 Amps1.7 AmpsYes up to 24 per boosterZ-HO/On30
lowest cost per frog
Dual Frog Juicer211.7-10 Amps2 or 4 Amps selectableLimited to about 4 per boosterlarger scales O-F
turntable reverser
auto reverser for wyes loops etc.
Mono Frog Juicer101.7-5 Amps1.7 AmpsLimLimited to about 4 per boosterZ-HO/On30


What are the pros and cons of a frog juicer vs a relay or switch?

Frogs need to be powered to prevent interruptions in power to your locomotives as they pass over a turnout.  Some turnouts have very short frogs or plastic frogs and this can be ignored.  Some modellers only run 8-wheel and 12-wheel diesels and don't need to power their frogs as they always have good contact.  However short diesels and steam locomotives often baulk at unpowered frogs.  It is embarrassing to have to get out the 0-5-0 to rescue a stalled locomotive. The issue with powering a frog is that you have to switch the power to the same polarity as the points when the turnout is thrown.  The frog juicer automatically switches the power on a frog.  A wire from the frog juicer is used to power the frog - if the frog is of the wrong polarity and shorts, the frog juicer detects the current surge and nearly instantaneously switches the power before the locomotive decoder or the command station can notice.

The other way to switch the power is by using a switch or relay connected to the turnout movement or the control panel.  Often a micro switch is used that is tripped by the movement.  These can be difficult to adjust and keep adjusted. Another method is to use a switch built-in to the switch motor (i.e tortoise, blue-point, bullfrog or cobalt).  These work well.  They occasionally wear out and in this case you could add a frog juicer if you don't want to replace the switch motor. 

Another strategy is to use a DPDT toggle to throw your turnout motors.  In this case one set of the contacts on the toggle are used for the turnout motor and the other is used to power the frog.  Toggle switches wear out over time but are usually relatively easy to replace.  On layouts I operate on regularly that use this method we need to replace a toggle every few operating sessions.

relay can often be used in place of toggles.  They can be connected to the logic that throws the turnout.  Some complex situations such as 3-way turnouts or double crossovers that may require ganged relays to implement the logic needed for the proper powering of frogs based on point position.  In this case a frog juicer is far simpler to implement.

The main advantage of the frog juicer is simplicity - just connect a single wire to the frog and power the juicer from the DCC bus and you are done.  Frog juicers are electronic and not subject to mechanical wear.

Finally, there are situations where a frog is not connected to moving points, like a crossing, and there is no mechanical or electrical way to easily switch the frog power.  In this case the frog juicer is ideal.

Some turnouts, such as Peco electrofrogs, use power-routing.  This is where the points touching the stock rails is sued to power the points and the frog as a unit.  this works really nicely for about a year and then no amount of cleaning seems to be able to restore good contact.  We have used hex frog juicers to restore these turnouts and make them operate better then new.  Just connect a wire from the point/frog assembly to the frog juicer output.  Using hex frog juicers with power-routing turnouts can also save you from modifying them to "DCC-friendly".  This is because the hex frog juicer will handle the shorts that can occasionally occur by a wheel bridging the gap between the open point and the stock rail.  Hex frog juicers have a special start-up sequence that sequences each turnout on one at a time and checks for a short and thus starts each turnout in the correct polarity.  The mono and dual cannot do this and this limits the number of electrofrogs you can connect to a command station through the frog juicers.  Otherwise you can get a situation where too many turnouts are in the wrong polarity for the booster to start the layout without immediately shutting down.  If this confuses you - all you have to remember is to use the Hex frog Juicer with electrofrogs.

Manufacturer : Tam Valley
SKU : HFJ003
EAN :
Coastal DCC Ltd
Registered Offices: Ipswich Model Railway Centre, 48-52 Tomline Road, Ipswich, IP3 8DB
Registration Number: 9447637 in England & Wales
Terms & Conditions | Privacy | Contact Us | Delivery Policy | Return Policy