Digitrax
Accessories
nrm-40020
New Rail Models - Throttle Pocket
Holder for your throttle fits handsets from Digitrax, NCE, Lenz & MRC/Gaugemaster.
This will NOT fit the new DT602 & UT6 handsets, use the Digitrax Stow-Away instead
more info on Throttle Pocket...This item is in Stock and available for dispatch
£6.50
Computer Interfaces
LNWI
LocoNet WiFi Interface
The LNWI allows you to connect compatible WiFi devices to LocoNet and run trains using compatible throttle apps.
Requires a 12 or 15v DC regulated Power Supply
Wi-Fi interface to a Digitrax LocoNet for up to four compatible... more ...
Loconet
more info on LocoNet WiFi Interface...This item appears to not currently be in stock
This item is on back order with our suppliers
£70.00
PR4
USB to LocoNet Interface
This will require an additional Power Supply if it is to be used in a standalone mode
The PR4 makes decoder programming and interfacing your layout and computer easier than ever. The PR4 seamlessly switches between computer interface and... more ...
Loconet
more info on USB to LocoNet Interface...This item appears to not currently be in stock
This item is on back order with our suppliers
£77.60
Power Management
PM42-BO
Acculites - PM42 Break Out Board
Break out board for the PM42 to replace the 44 way connector that brings all the pins to screw terminals rather than solder tabs.
more info on PM42 Break Out Board...This item appears to not currently be in stock
But is still available to order
£35.00
PM74
Power Manager
4 Power Manager sub-districts.
Upgraded replacement for PM42, fully encased.
Fully connectorized installation.
Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit... more ...
more info on Power Manager...This item appears to not currently be in stock
This item is on back order with our suppliers
£91.94
AR1
SINGLE AUTO REVERSER
8 amp Auto-reversing control for a single reversing district.
Simple to wire.
Tunable trip current lets you use it on any layout from Z to G.
AR1 operates with or without LocoNet so, it can be used on... more ...
more info on SINGLE AUTO REVERSER...Only 1 remaining in stock
£28.00
BXPA1
LocoNet DCC Auto-Reverser
The BXPA1 is a combination DCC Auto-Revereser, occupancy detector, Transponding detector, and intelligent power manager. It is designed to make transponding implementation easy and provide advanced DCC track management by communicating all state... more ...
Loconet
more info on LocoNet DCC Auto-Reverser...This item appears to not currently be in stock
This item is on back order with our suppliers
£41.00
Signals
SH2AB
HO Scale Mainline Signaling Kit
This product is intended for use with the SE8C.
Makes all of your signals plug ‘n play with small 10 pin connectors.
Can be used as a basic N or HO scale signal.
Mounting board and hardware... more ...
more info on HO Scale Mainline Signaling Kit...This item is in Stock and available for dispatch
£19.20
SHABC
H0 scale Turnout Signaling Kit
This product is intended for use with the SE8C.
Makes all of your signals plug ‘n play with small 10 pin connectors.
Can be used as a basic N or HO scale signal.
Mounting board and hardware... more ...
more info on H0 scale Turnout Signaling Kit...This item is in Stock and available for dispatch
£21.00
SN2AB
N Scale Mainline Signaling Kit
This product is intended for use with the SE8C.
Makes all of your signals plug ‘n play with small 10 pin connectors.
Can be used as a basic N or HO scale signal.
Mounting board and hardware... more ...
more info on N Scale Mainline Signaling Kit...This item is in Stock and available for dispatch
£22.00
Page (14) of (18)