DCC Specialties - Block Watcher
DCC Specialties and Integrated Signal Systems (ISS) collaborated to develop and design the BlockWatcher. The need was due to the fact that at the higher amperages required by high density users, most existing products either create a substantial... more ...
more info on Block Watcher...This item is in Stock 2-4 Working Days Delivery Available
DCC4PC - Rail Comm Reader
The 16 Zone Local RailCom™ Reader Device
Our RailCom™ Reader device, unlike some others on the market, can cope with more than one RailCom™ enabled locomotive in a single zone, and it can distinguish between Short addresses, Long addresses and... more ...
more info on Rail Comm Reader...Only 1 remaining in stock
Digitrax - QUAD OCCUPANCY DETECTOR
Cost Effective occupancy detection for 4 detection sections
Outputs for panel mounted LEDs to display occupancy
Detects any powered locomotive
Detects un-powered rolling stock equipped with resistor wheel... more ...
more info on QUAD OCCUPANCY DETECTOR...This item appears to not currently be in stock
Digitrax - Remote Diode
Remote sensing Diode for BDL168
more info on Remote Diode...This item is in Stock 2-4 Working Days Delivery Available
Lenz - LB101 Occupancy Module
In order to detect the status of tracks the LB101 functions as a current sensor, and is inserted between the LR101 and the monitored track section. The LB101 can monitor two track sections independently from each other.
General information... more ...
more info on LB101 Occupancy Module...This item is in Stock 2-4 Working Days Delivery Available
Lenz - LB050 Voltage Detector
Status detection via current sensors, such as the occupancy detector LB101, has one crucial disadvantage: if the operating voltage is interrupted, so is the power supply. In this case, occupancy detection fails: the signal output will report unoccupied... more ...
more info on LB050 Voltage Detector...Only 1 remaining in stock
Lenz - LRC120 RailCom Address display
This 4-digit display serves to depict the address of the locomotive located in a monitored track section. Installation is possible anywhere on the layout, for example inside a signal box.
more info on LRC120 RailCom Address display...Only 1 remaining in stock
Lenz - LW150 Mimic panel module
Construct a mimic panel for your layout using the LW150. 16 accessory addresses may be controlled (Points and signals). 32 LEDs can also be powered to show the position of the 16 accessories.
more info on LW150 Mimic panel module...Only 1 remaining in stock
Littfinski DatenTechnik - LDT-01 Detector Case
This item appears to not currently be in stock
Littfinski DatenTechnik - LDT-02 Detector Case
more info on LDT-02 Detector Case...Only 1 remaining in stock
NCE - BD20 Block Detector
Detects DCC current being drawn in a block. Connects to AIU01 or most commercial signal systems.
more info on BD20 Block Detector...This item is in Stock 2-4 Working Days Delivery Available
Roco - Digital Feedback Module
The feedback module 10787 form the basis of all automatic functions of the system that are to be executed with the PC software Rocomotion. This module is also a necessary installation for safeguarding functions for train trips... more ...
more info on Digital Feedback Module...Only 1 remaining in stock
RR-CirKits - Current Sensing Coils
Set of 6 CT (Current Transformer) coils for the LNCP. These 100:1 toroid coils sense the track current on leads passing through the hole in the middle of the coil.
more info on Current Sensing Coils...This item is in Stock 2-4 Working Days Delivery Available
RR-CirKits - Block Occupancy Detector
Block Occupancy Detector for 8 Blocks, requires a set of 8 CT-coils
more info on Block Occupancy Detector...Only 1 remaining in stock
RR-CirKits - 8x Current Sensing Coils
Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through the hole in the middle of the coil.
more info on 8x Current Sensing Coils...This item is in Stock 2-4 Working Days Delivery Available
RR-CirKits - Single Block Occupancy Detector
This inexpensive self contained diode drop detector works with both analog DC and DCC layouts. It has dual opto isolator outputs which allow it to drive virtually any signal logic designs.
more info on Single Block Occupancy Detector...This item is in Stock 2-4 Working Days Delivery Available
RR-CirKits - WatchMan
Includes 8 detector amplifiers for DCC current Detection. Coils not included.
Detection levels adjustable from 1⁄2 ma to 20 ma DCC. (20K ohm or less)
Train current maximum of 10A or... more ...
more info on WatchMan...This item is in Stock 2-4 Working Days Delivery Available
Team Digital - DCC Block Detector
The DBD22 is a dual block occupancy detector. It provides complete isolation from the track by using small transformer type sensors. This also means there is no drop in track voltage as there is with sensing diodes. The DBD22 is designed to work well... more ...
more info on DCC Block Detector...This item appears to not currently be in stock
Uhlenbrock - GBM Occupancy detector with switching relay
The most frequent use for this module is to provide a reliable track plan panel so that you know at any time which track is already occupied and which is vacant.
more info on GBM Occupancy detector with switching relay...This item appears to not currently be in stock
This item is on back order with our suppliers
Uhlenbrock - Lissy Starter Set
Contains 2 Transmitters, 1 Receiver, LocoNet cable and Manual
more info on Lissy Starter Set...Only 1 remaining in stock
Uhlenbrock - Lissy Shuttle Set
Pre-configured set of LISSY receivers to control a shuttling train on a single track. May be installed on a layout without any further programming. The modules may be re-programmed to perform like any other LISSY receiver. Works with Intellibox, Twin... more ...
more info on Lissy Shuttle Set...This item appears to not currently be in stock